Raymarine RS232 Instalační manuál

PC/SeaTalk/NMEAInterface BoxOwner’sHandbookDocument number: 81166-3Date: 1 February 2002166_3cov.p65 24/01/02, 11:211

8PC/SeaTalk/NMEA Interface Box3.1 NMEA OutputProvided you have the appropriate SeaTalk instrumentation, thedata listed below is transmitted in NMEA 01

Operation and Installation 9GPS Antenna Height GGAGPS Quality Indicator GGAHeading (Magnetic or True) HDM, HDG, VHW, HDTLatitude & Longitude GGA,

10PC/SeaTalk/NMEA Interface BoxCablingThe PC/SeaTalk/NMEA Interface should be connected to SeaTalkand the other manufacturer's equipment as follo

Operation and Installation 113.2 NMEA InputThe PC/SeaTalk/NMEA Interface can also be used to convert NMEA0183 data to SeaTalk. NMEA 0183 data is also

12PC/SeaTalk/NMEA Interface BoxData NMEA HeaderGPS Number of Satellites GGAGPS Antenna Height GGAGPS Quality Indicator GGAHeading (Magnetic or True) H

Operation and Installation 13Cabling (ST1,2,3000 autopilots)D5509-1Screen (0v)Yellow (Data)Screen(0v)NMEASEATALKALARMOUT+ –IN+ –OUT+ –RS232SEATALKN

14PC/SeaTalk/NMEA Interface Box3.3 Main AlarmThe PC/SeaTalk/NMEA Interface can be used to drive theRaymarine Main Alarm (Cat No Z035). This alarm will

Operation and Installation 15CablingThe Main Alarm should be wired to the PC/SeaTalk/NMEAInterface as follows:NMEASEATALKALARMOUT+ –IN+ –OUT+ –RS23

16PC/SeaTalk/NMEA Interface Box3.4 Connecting a Personal ComputerThe PC/SeaTalk/NMEA Interface can be used to send or receiveSeaTalk and NMEA data to

Operation and Installation 17NMEASEATALKALARMOUT+ –IN+ –OUT+ –RS232SEATALKNMEA+ –D1773-2Red(v+)Screen(0v)+-Power5AScreen (0v)Red (v+)Yellow (Data)

Copyright © Raymarine Limited 2002166_3cov.p65 24/01/02, 11:212

18PC/SeaTalk/NMEA Interface BoxPC Serial Port Connections to NMEAThe following diagram shows the pin connections for 25-pin and9-pin PC serial ports t

Operation and Installation 193.5 Connecting to a PC with RayTech NavigatorThe PC/SeaTalk/NMEA Interface can be used to connect aSeaTalk system to a pe

20PC/SeaTalk/NMEA Interface BoxChapter 4: Fault FindingAll Raymarine products are comprehensively tested prior to packingand shipment. In the unlikely

Operation and Installation 21Servicing and Safety• Raymarine equipment should be serviced only by authorised Raymarineservice technicians. They will e

22PC/SeaTalk/NMEA Interface Box166_3chs.p65 24/01/02, 11:2122

Operation and Installation 1ContentsChapter 1: Introduction ... 3Chapter 2: Mounting ...

2PC/SeaTalk/NMEA Interface BoxEMC ConformanceAll Raymarine equipment and accessories are designed to the bestindustry standards for use in the leisure

Operation and Installation 3Chapter 1: IntroductionSeaTalk is the language used by Raymarine products to shareinformation. This is unique to Raymarine

4PC/SeaTalk/NMEA Interface BoxChapter 2: MountingSelect a suitable location that is:• away from direct contact with water• clean and grease-free• acce

Operation and Installation 53. Alternatively, the PC/SeaTalk/NMEA Interface box may beattached using the 2 self tapping screws provided.4. Remove the

6PC/SeaTalk/NMEA Interface BoxChapter 3: Operation/WiringEMC Installation GuidelinesAll Raymarine equipment and accessories are designed to the best i

Operation and Installation 7damage the equipment, but may cause the loss of some information and maychange the operating mode.• Raymarine specified ca